ДОБРО ПОЖАЛОВАТЬ В НАШ БЛОГ

Мы делимся знаниями в областях, которые нас больше всего увлекают.
click

10mm Clear Tempered Glass Panels for Construction Projects

От lydglass September 8th, 2026 24 просмотров

Introduction: Project contractors specifying 10mm clear tempered glass panels need to match the published product range with the finished opening, edge treatment, frame, hardware, and quantity before production begins.

A clear tempered glass request becomes useful when a drawing, panel schedule, or measured opening is converted into a precise production specification. LYD-CTG10 is listed as 10mm thick, with a Clear surface and Flat edge and Polished edges. Its published size range runs from 100mm x 100mm to 3660mm x 2440mm. These details give contractors, fabricators, and project buyers a defined starting point for partitions, furniture panels, doors, windows, and architectural installations. The practical decision is to confirm the finished dimensions and edge condition before tempering, then submit a complete panel schedule for review.

What 10mm Clear Tempered Glass Specifies for a Custom Panel

A useful specification begins with the product identity and then adds the requirements for each individual panel. LYD-CTG10 is identified as 10mm Clear Tempered Glass under the Custom Tempered Glass Panels description. The 10mm thickness establishes the requested glass configuration. It is a clear starting specification for projects using glass partitions, doors, windows, furniture panels, and other architectural elements. Structural suitability remains a separate design decision based on the support arrangement, installation system, project requirements, and applicable local rules. “Clear” describes the transparent surface selected for this model. It is appropriate wording when a project calls for a transparent panel that allows light through while retaining a plain glass appearance. Clear should be kept distinct from terms such as ultra-clear, low-iron, tinted, frosted, or patterned, because those descriptions represent different appearance requirements. In a request for quotation, stating “10mm clear tempered glass” prevents the surface requirement from becoming an open-ended color or finish discussion. The edge description is equally important. LYD-CTG10 is published with a Flat edge and Polished edges. This identifies a straight panel edge with a finished polished surface. A polished flat edge can be relevant where the edge remains visible on a furniture panel, partition, or door, and it also needs to be coordinated where the edge enters a frame, channel, gasket, or hardware system. The product description identifies the glass configuration; the project drawings and installation details determine how that configuration is used. A clear inquiry can state the model, thickness, surface, edge condition, finished dimensions, and quantity in one line: “LYD-CTG10, 10mm, Clear, Flat edge and Polished, 1,200mm x 2,100mm, 18 panels. ” This format gives the supplier a defined production starting point and separates the product specification from broader engineering or installation decisions.

How Panel Dimensions and Edge Finishing Shape Fabrication Decisions

Panel dimensions must be developed from the complete assembly rather than copied automatically from a rough opening. The opening size, frame profile, gasket, setting block, clearance, joint arrangement, hardware, and required tolerance can all influence the finished glass size. A measured opening is therefore an input to the specification, while the finished glass dimension is the value used for production. This distinction matters when several panels appear similar. An office partition may have repeated heights but different bay widths. Furniture panels may share an appearance while fitting separate recesses. Door and window glass may depend on the exact frame and hardware layout. A panel schedule should identify each finished width and height, distinguish fixed panels from door leaves, and show quantities for repeated sizes. That approach gives the supplier information that can be checked against the complete project request.

1. The Published Size Range Defines the Starting Point for Project Fit

LYD-CTG10 has a published minimum size of 100mm x 100mm and a maximum size of 3660mm x 2440mm. This is the product’s stated starting range for custom tempered glass panels. A small furniture insert may sit close to the minimum, while a large architectural panel may approach the maximum. Both situations benefit from early review because the final production request also depends on the drawing, edge treatment, frame details, handling conditions, and any additional work requested for the order. A dimension within the published range still belongs in the project-specific schedule. For example, a package combining fixed partition panels and glass doors should list every finished size separately, even when all pieces use 10mm Clear glass. Doors can have different dimensions from adjacent fixed panels, and a repeated nominal size can conceal differences in hardware or frame interfaces. Organizing the schedule by finished dimensions and quantities makes the production mix easier to review before tempering.

2. Flat Polished Edges Must Match the Intended Frame or Hardware

“Flat edge and Polished” communicates a straight edge with a finished polished surface. It is more precise than a general request for “finished edges,” particularly when the edge will be visible or handled during installation. For a furniture panel or exposed partition edge, the visible finish is part of the design discussion. For framed glass, the channel, gasket, clearance, and retention method need to accommodate the specified panel edge. The edge should therefore be connected to the project drawing. Mark whether it will remain exposed, sit inside a channel, be covered by a gasket, or meet another panel. The frame or hardware provider may have dimensional requirements that affect the finished glass. LYD-CTG10 is published with Flat edge and Polished edges; other edge conditions and additional processing for this exact model should be discussed before the order is released.

Why Every Final Dimension is worth checking Before Tempering

Tempering heats glass and then rapidly cools it to create the tempered state. The manufacturing sequence follows the earlier cutting and edge-preparation stages, so the finished shape and dimensions must be settled before the glass enters tempering. LYD-CTG10 product information emphasizes accurate measurement before tempering, and tempered glass cannot be cut or modified afterward. A missed dimension therefore requires a production correction rather than a later site adjustment. The same timing applies to any requested holes, slots, edge work, or LOGO processing. The current model is specifically published with a Clear surface and Flat edge and Polished edges. Other colors, edge types, holes, slots, and LOGO processing for this exact model require confirmation. If such details appear on the architectural drawing, include them in the inquiry before production so the supplier can review their availability and sequence. Quantity control should accompany dimension control. Group panels that share one finished size and list different sizes separately. Include the product model, thickness, surface, edge condition, finished width and height, quantity, frame or hardware information, and any requested processing. This gives the supplier a practical basis for checking the panel schedule against the intended installation system. Before tempering begins, compare the schedule with the latest drawing, the final frame dimensions, hardware details, edge requirements, tolerances, and quantity summary. Changes resolved at this stage help keep the 10mm clear tempered glass order aligned with the project’s actual requirements. Packaging and shipping discussions, including options such as plywood crates or an A-Steel Rack and shipment through Xingang Port, can follow once the production specification is clear.

Conclusion

LYD-CTG10 provides a defined specification for 10mm Clear Tempered Glass: Clear surface, Flat edge and Polished edges, and a published size range from 100mm x 100mm to 3660mm x 2440mm. Contractors should compare each finished panel dimension and edge condition with the frame, hardware, drawing, tolerance, and quantity schedule before production. Because tempered glass cannot be cut or modified after tempering, accurate pre-tempering information is essential. Send LYD GLASS the product model, finished dimensions, quantities, edge requirements, and any requested processing for review, quotation, and order planning.

FAQ

Q:What are the minimum and maximum sizes for LYD-CTG10 tempered glass panels?

A:The published minimum size for LYD-CTG10 is 100mm x 100mm, and the published maximum size is 3660mm x 2440mm. Each finished panel should be matched with the project drawing, frame, hardware, tolerances, and processing requirements before production.

Q:What does Flat edge and Polished mean for a 10mm glass panel?

A:For a 10mm glass panel, Flat edge and Polished means a straight panel edge with a finished polished surface. The edge should be coordinated with the intended frame, channel, gasket, or hardware so the finished glass suits the installation detail.

Q:Can 10mm tempered glass panels be cut after tempering?

A:No. Final dimensions and required fabrication must be completed before tempering because tempered glass cannot be cut or modified afterward. Holes, slots, edge work, LOGO processing, and other requested details should be included in the drawing and confirmed before production.

Sources / References

What is glass? How is glass made?

Glass - Chemistry Encyclopedia

Glass for buildings

LYD GLASS 10mm Clear Tempered Glass

Назад
Tempered Glass Manufacturing for Custom Building Projects
Читать далее
Далее
Architectural Tempered Glass Panels for Commercial Interiors
Читать далее
категория блога

СВЯЗАТЬСЯ С НАМИ

Если у вас есть вопросы, свяжитесь с нами сегодня! Не стесняйтесь. Мы стараемся сделать дополнительный шаг для удовлетворения наших клиентов.
Имя *
Электронная почта *
WhatsApp *
Сообщение *
Leave a message
Имя *
Электронная почта *
WhatsApp *
Сообщение *
Мы используем Печенье для улучшения вашего опыта работы в Интернете. Продолжая просмотр этого веб-сайта, мы предполагаем, что вы соглашаетесь с нашим использованием Печенье .